stainless steel bolt torque specifications
Torque Information - Fuller Fasteners : Fuller Fasteners
Example: A M30-12.9 fastener has a maximum tightening torque of 2,280 Nm, based on a friction coefficient of 0.125 (zinc plated) Maximum torque: 2,280Nm (= 123%) (or 117%)
Get priceBolt Torque Charts - AFT Fasteners
Values calculated using industry accepted formula T = KDP where T = torque, K = torque coefficient (dimensionless), D = nominal diameter (inches), P = bolt clamp load (lbs). K values: waxed (e.g. pressure wax as supplied on high strength nuts) = .10, hot dip galvenized = .25, and plain non-plated bolts .
Get price
STANDARD STAINLESS STEEL - Mettex
These specifications apply to fasteners (primarily bolts, screws and nuts) made from austenitic grades of corrosion-resistant stainless steels with sizes from 1,6 up to and including 39 mm, metric (ISO) thread and also to nuts with widths across flats or outside diameters ≥ 1,45 d and an effective thread engagement of at
Get price
Bolt Depot - US Recommended Bolt Torque Table
Size Recommended Torque; Grade 2 Grade 5 Grade 8 18-8 S/S Bronze Brass; Coarse Fine Coarse Fine Coarse Fine Coarse Fine Coarse Fine Coarse Fine #4*-----5.2-4.8-4.3
Get price
Why Stainless Steel Heavy Hex Bolts Tend To Seize | Melfast
Why Stainless Steel Heavy Hex Bolts Tend To Seize Some contractors and assemblers complain about stainless steel heavy hex bolts seizing during the tightening process. This happens with other stainless steel bolts as well, although galvanized heavy hex bolts do not seem to have the same problems. Frequent seizing is often a result of galling, [.]
Get price
Bolt Torque Chart - Duplex Steel Fasteners Manufacturers
The bolt is stressed up to the proofload value, and if there is no deformation, elongation, or fracture, then the bolt is deemed to have passed. For bolting specifications that do not have a published proofload, it is usually calculated at 92% of ultimate yield strength. 2 - Clampload is calculated at 75% of proofload. This is done to allow a ...
Get price
AN-MS-NAS Aircraft Hardware
AN3 thru AN20 - AIRFRAME BOLTS Steel - Cadmium plated per QQ-P-416, Type II, Class 3. Aluminum Alloy. 431 Stainless Steel (CRES). Minimum Tensile Strength (Steel and CRES) - 125,000psi. See Chart AN42 thru AN49 EYEBOLTS Steel - Cadmium plated per QQ-P-416, Type II, Class 3. CRES.
Get price
Standard Torque Settings For Stainless Steel Metric Bolts ...
Feb 02, 2018· A286 Stainless Steel Bolts Astm A453 Gr 660 Hex Nut Stud Fasteners Bolt Torque Chart Stainless Steel Banjo Torque Specs Hose And Ings Source ... Determining torque the facts about required tension and clamp loads fastener torque specs fastener torque specs banjo torque specs hose and ings source. Share this: Click to share on Twitter (Opens in ...
Get price
Suggested Assembly Torque Values - Nuts and Bolts
Suggested Assembly Torque Values ... Generally the full effort of an ironworker with a ordinary spud wrench is sufficient to tighten the nuts on anchor bolts. ... 304 Stainless Steel: 316 Stainless Steel ASTM A193 Grade B8: ASTM A193 Grade B8M 1/4 - 2 1/2" 1/2 - 4" 1/2 - .
Get price
ASTM F593 - Portland Bolt
ASTM F593 covers the chemical and mechanical requirements for stainless steel bolts, hex cap screws, and studs in diameters ranging from 1/4″ to 1-1/2″ inclusive. These fasteners are for general purpose usage and are available in seven alloy groups. Below is a basic summary of the common grades within the ASTM F593 specification.
Get priceTORQUE-TENSION REFERENCE GUIDE - Fastenal
TORQUE-TENSION RELATIONSHIP FOR A307A, GRADE 5, 8 & 9 BOLTS Locknut Size Threads per inch Steel Hex Locknut Steel Hex Flange Nut Grade C FNL Grade 9 Grade F Grade G Clamp Load (lbs.) Tightening Torque Clamp Load (lbs.) Tightening Torque Clamp Load (lbs.) Tightening Torque Clamp Load (lbs.) Tightening Torque min max min max min max min max
Get price
RIVNUT Fastener Engineering Data - Unified Thread
Aluminum Steel Stainless Steel Min. Grip Max. Grip Min. Grip Max. Grip Min. Grip Max. Grip #4-40 400 450 700 800 800 900 ... Torque strength data Torque - axial load relationship ... type and property class of screw or bolt, it is recommended that a ...
Get price
Recommended Torque Values - SEFCOR
Recommended Torque Values . For hardware consisting of a hex head bolt, hex nut and spring lock washer. Silicon Bronze Hardware Aluminum Hardware Galvanized Steel Hardware Stainless Steel Hardware Dia. in-lb ft-lb N-m in-lb ft-lb N-m in-lb ft-lb N-m in-lb ft .
Get price
STANDARD TORQUE VALUES - METRIC SYSTEM
TM 10-4330-237-13&P STANDARD TORQUE VALUES-METRIC SYSTEM In the absence of specific torque values, the following chart can be used as a guide to the maximum safe torque for a particular size/grade of fastener. There is no torque difference for fine or coarse threads. Torque values are based on clean, dry threads. Reduce value by 10% if threads ...
Get price
FASTENER REFERENCE GUIDE
A 304 Stainless Steel used for high temperature applications. This material has been carbide solution treated in the finished condition. ASTM A193/A193M B8M Class 1 All 75,000 30,000 B96 A 316 Stainless Steel used for high temperature applications. This material has been carbide solution treated. ASTM A193/A193M B8MA Class 1A All 75,000 30,000 B90
Get price
ARP | Official Website | ARP Ultra-Torque
First, let's be clear: ARP provides torque specs for our fasteners based on using ARP Ultra-Torque. If you're not using our specs and our lube, you have no real idea what pre-load you're getting. We've done the testing where we can measure the torque applied and the resulting pre-loads.
Get price
Stainless Steel & Stainless Steel Fasteners
Product Specifications ASPEN FASTENERS Stainless Steel Tel.: 1-800-479-0056 Fax: 1-888-411-2841 [email protected] Stainless Steel & Stainless Steel Fasteners Chemical, Physical and Mechanical Properties
Get priceASTM A193/A193M B8 and B8M Class 1 Torque-Tension Guide
The torque values can only be achieved if nut (or tapped hole) has a proof load greater than or equal to the bolt's minimum ultimate tensile strength. UN8 Thread Series Caution: Stainless steel fasteners tend to gall, especially with long run downs, prevailing torque fasteners, impact drivers, and lack of lubrication.
Get priceASTM A354-BD / SAE GRADE 8 Bolt Torque Chart
A354 grade BD bolts are stronger than A354 grade BC. SAE J429 Grade 8 bolts are made of medium carbon alloy steel. The given below ASTM A354-BD / SAE GRADE 8 Bolt Torque Chart provides you with torque of various corresponding bolt sizes along with its TPI, clamp load and proof load . SAE J429 grade 8 bolts do not exceed 1.5 inches diameter.
Get price
ASTM A193, 316 Stainless Steel Bolts, Stainless Steel 316 ...
316 Stainless Steel Bolts Stainless Steel UNS S31600 Bolts, SS DIN 1.4401 Bolt, Dimensions of ASME B18.2.1 Hex Bolts, Stainless Steel 316 Bolts, SS B8M Bolts, B8M Stainless Steel Bolt, Stainless Steel B8M Class 1 Bolt, 316 SS Industrial Bolts, SUS 316 Bolt Manufacturer in Mumbai, India
Get price
Torque Table Standard Bolt Sizes SAE - Engineers Edge
Bolt Size: 18-8 Stainless Steel : Brass: Aluminum 2024-T4: 316 Stainless Steel: Nylon: 2 - 56: 2.5: 2.0: 1.4: 2.6: 0.44: 4 - 40: 5.2: 4.3: 2.9: 5.5: 1.19: 4 - 48: 6.6 ...
Get price
RECOMMENDED ASSEMBLY TORQUES
Surface Condition Torque Adjustment Factors Plain Steel, as supplied X 1.0 Plain Steel, degreased X 2.0 Zinc Plated, as supplied X 1.0 Zinc Plated, lightly oiled X 0.9 Galvanised, degreased X 2.1 Galvanised, lightly oiled X 1.1 Heavily greased X 0.7 RECOMMENDED ASSEMBLY TORQUES Class 10.9 ISO Metric Coarse Pitch Bolts & Screws Bolt Tension ...
Get price
Fastener Torque Specs - Extreme-Bolt & Fastener
In the case of bolts and nuts, this elastic deformation between the bolt head and the nut is critical in order to create tension or clamping force to hold the joint together. The amount of torque applied is a function of the frictional forces and bolt diameter and is typically calculated utilizing a clamp load equaling 60-70% of the yield.
Get price
ASTM F593 Specification - Boltport Fasteners
ASTM F593 - Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Stud Bolts. This specification covers the requirements for stainless steel bolts, hex cap screws, and stud bolts in imperial size 0.25 inch to 1.50 inch, inclusive for number of alloys in common use and intended for service applications requiring general corrosion resistance.
Get priceStandard Specification for Stainless Steel Bolts, Hex Cap ...
1.1 This specification covers the requirements for stainless steel bolts, hex cap screws, and studs 0.25 to 1.50 in., inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance.
Get price
Bolt Torque Chart - Duplex Steel Fasteners Manufacturers
The bolt is stressed up to the proofload value, and if there is no deformation, elongation, or fracture, then the bolt is deemed to have passed. For bolting specifications that do not have a published proofload, it is usually calculated at 92% of ultimate yield strength. 2 - Clampload is calculated at 75% of proofload. This is done to allow a ...
Get price
CDI-Torque: Bolt Torque Specifications • JM Test Systems
31 · Bolt Size Inches: Coarse Thread/ inch: SAE 0-1-2 74,000 psi Low Carbon Steel: SAE Grade 3 100,000 psi Med Carbon Steel: SAE Grade 5 120,000 psi Med. Carbon Heat T. Steel: SAE Grade 6 133,000 psi Med. Carbon Temp. Steel: SAE Grade 7 133,000 psi
Get priceWhy Stainless Steel Heavy Hex Bolts Tend To Seize | Melfast
Why Stainless Steel Heavy Hex Bolts Tend To Seize Some contractors and assemblers complain about stainless steel heavy hex bolts seizing during the tightening process. This happens with other stainless steel bolts as well, although galvanized heavy hex bolts do not seem to have the same problems. Frequent seizing is often a result of galling, [.]
Get price
ASTM A193 Grade B8 Specification - Boltport Fasteners
ASTM A193 Grade B8 Specification for high tensile bolts, screws, stud bolts, anchor bolts, threaded rods, round bars and other externally threaded fasteners, made from 304 stainless steel. ASTM A193 specification covers requirements for chemical composition, mechanical properties, heat-treatment, hardness, recommended nuts-washers and markings for Grade B8 fasteners.
Get price
Bolt Torque Calculator - Determining Proper Torque to Bolt ...
Standard specification for structural bolts, alloy steel, heat-treated. ½ to 1½ in. 150,000 psi. ASTM A193 B7. Standard specification for alloy-steel and stainless steel bolting for high temperature or high-pressure service and other special purpose applications. Up to .
Get priceStainless Steel Pre-load and Tightening Torques
Thread Coeff Friction Preload (Kn) Property class Tightening Torque (Nm) Property class Min Breaking Torque; A1-50 A2-70 A4-80 A1-50 A2-70 A4-80 A1-50 A1-70
Get price
Torque Values for A2-70 or A4-70 Metric Stainless Steel ...
The torque values can only be achieved if nut (or tapped hole) has a proof load greater than or equal to the bolt's minimum ultimate tensile strength. Torque values calculated from formula T=KDF, where Lubricated Clamp Load F based on 75% of Yield Dry Clamp Load F based on 40% of Yield to avoid Galling. K = 0.16 for "lubricated" conditions
Get price